Welcome to our Facmaster Factory!

Commutator Grinding Line

  1. Home
  2. Blog
  3. Commutator Grinding Line
COMMUTATOR GRINDERS

Commutator Grinders

The following 9 pages describe our complete line of commutator grinding tools. The three salient factors in choosing a commutator resurfacing tool are 1. Commutator bar length or width of slip ring matched to grinding capacity of tool. 2. Access area matched

Online TruingGrinding Cutsforth Inc

Online Truinggrinding Cutsforth Inc

Commutator grinding, surfacing or machining Collector ring or commutator stoning Benefits of Online Truing versus Offline grinding On-line truing is typically more cost effective and less time consuming. No need to take the unit offlineNo downtime needed to perform service. No lost revenue to perform our Online Truing Service.

FOR TOTAL COMMUTATOR MAINTENANCE

For Total Commutator Maintenance

During grinding, move the stone slowly from side to side. This will prevent ridges in the commutator from wearing grooves in the stone. Large stones which are difficult to move while grinding may be held in one place for a few seconds, then lifted, moved about 14 inch, applied again

Guide to Selection Of Grinders and Shredders Franklin Miller

Guide To Selection Of Grinders And Shredders Franklin Miller

In-line ComminutorsGrinders. The first machine to address the problems of reducing solids directly inline was the Pipeline Delumper. Originally developed in the 1960s for the chemical process industry, this pressure rated unit quickly became invaluable to treatment plants. ... These combined grinding and screening systems have been ...

Commutator an overview ScienceDirect Topics

Commutator An Overview Sciencedirect Topics

In the absence of this tool, the second preferred method is to use a grinding stone and to turn the commutator. This operation would also be performed in the motor shop. If the commutator is not too far out of round, and the motor needs to be back on the line quickly, a handstone specified for smoothing commutators can be used.

TRUING COMMUTATORS and SLIPRINGS

Truing Commutators And Sliprings

the commutator. The grain of the grinding wheel should be medium for rough truing, and fine for the finishing operation. Ensure that the grinding wheel does not clog, for this may cause lapping of the copper. The cuts must be small of the order of 2 to 3100 mm, in

CONDITION OF THE SURFACE OF COMMUTATORS AND

Condition Of The Surface Of Commutators And

OF COMMUTATORS AND RINGS-ROUGHNESS ... On the other hand, if the final surface is too rough, the commutator works rather like a grinding wheel and as a result excessive wear of the brushes occurs. From this, it will be seen that the roughness of commutators and rings must be confined to certain limits, and it is for this ... The line D is ...

MAINTENANCE OF CARBON BRUSHES BRUSH

Maintenance Of Carbon Brushes Brush

preferably with an M medium grain grade of grinding stone, or else use 80-grit sandpaper maximum 100-grit. After grinding or machining we recommend the following roughness values Ra 0.9 to 1.8 m 35 to 71 micro-inches for industrial machine commutators Ra

Common Collector Ring Problems Cutsforth Inc

Common Collector Ring Problems Cutsforth Inc

Collector rings and commutators are grooved from mechanical and electrical brush wear. Unfiltered air and oil contamination can increase the ring wear as well. Cutsforth Online Truing Service can restore the ring surface without shutting down. Worn or missing spiral groove

Carbon Brush amp Holder Technical Handbook

Carbon Brush Amp Holder Technical Handbook

A commutator or slip ring surface can be reconditioned in any one of seven ways, although other methods have been used in emergencies. The recognised and approved techniques are listed below in order of preference 1. Turning with a diamond tipped tool 2. Turning with a tungsten carbide tipped tool 3. Grinding with a rotating wheel 4.

CONDITION of the SURFACE of COMMUTATORS and

Condition Of The Surface Of Commutators And

of COMMUTATORS and RINGS-ROUGHNESS ... On the other hand, if the final surface is too rough, the commutator works rather like a grinding wheel and as a result excessive wear of the brushes occurs. From this, it will be seen that the roughness of commutators and rings must be confined to certain limits, and it ... The line D is such that the ...

Diamond D Products for

Diamond D Products For

mutator. When the commutator is clean and bright all the way around, the grinding is finished and no more copper has been removed than was absolutely necessary. The use of hand stones on any commutator even with large flats if the stone is twice as long as the width of the flat spot will not leave the commutator eccentric unless it is already so.

Method for trueing commutators and slip rings GRUTZA

Method For Trueing Commutators And Slip Rings Grutza

FIG. 3 is a broken elevational view taken generally along the line III--III of FIG. 2 but modified by canting the motor axis slightly with respect to the commutator axis in accordance with the principles of the present invention and showing the grinding wheel midway through its traverse of the width of the commutator, showing removal of copper ...

Commutator rounding brush General Electric Company

Commutator Rounding Brush General Electric Company

Commutator rounding brush - General Electric Company. Title Commutator rounding brush. United States Patent 4034249. Abstract An electrical contact brush having interposed in a central longitudinal slot an abrasive element which frictionally contacts the commutator surface at crests where the radius of curvature of the commutator is less than ...

COMMUTATOR GRINDERS

Commutator Grinders

commutator grinding and turning tools straight 6 grinding capacity base lengths from 6 to 48, grind from 6 to 50 long dimensions 6 to 48 l. 8-12 handle x 3-34 w. 4-58 handle x 7 h. required supports right-angle 6 grinding capacity base lengths from 6 to 48, grind from 6 to 50 long

Online TruingGrinding Cutsforth Inc

Online Truinggrinding Cutsforth Inc

Online Truing can provide greater accuracyOnline allows you to grind your rings and commutators at operational temperature and speed. This allows the out-of-roundness of your rings to be ground in reference to the operational center. A round ring on turning gear doesnt always equal a round ring online.

FOR TOTAL COMMUTATOR MAINTENANCE

For Total Commutator Maintenance

During grinding, move the stone slowly from side to side. This will prevent ridges in the commutator from wearing grooves in the stone. Large stones which are dicult to move while grinding may be held in one place for a few seconds, then lifted, moved about 14 inch, applied again for a few seconds, moved again, and so on until the commutator is true.

Guide to Selection Of Grinders and Shredders Franklin Miller

Guide To Selection Of Grinders And Shredders Franklin Miller

An important use for comminutors grinders is in the primary treatment of raw sewage solids in plant headworks and pump stations. Large, stringy solids can easily plug even supposedly non-clog pump impellers and necessitate the use of size reduction devices.

TRUING COMMUTATORS and SLIPRINGS

Truing Commutators And Sliprings

The medium grain grinding stone will be suitable for the majority of cases. IMPORTANT POINTS 1 After truing, the surface state should correspond with the defined conditions in our Technical Note STA BE 16-1. These are Large Commutators Ra 0.9 to 1.8 m. Small Commutators Ra 0.5 to 1 m. Steel or bronze rings Ra 0.75 to 1.25 m.

TOOLS amp DEVICES MERSEN

Tools Amp Devices Mersen

To achieve this proper roughness, the commutator or the slip ring has to be ground after machining with a medium grinding stone such as PN 90623N. If you wish to work without dismantling the machine, rather use a grinding stone with a handle. PN 90602N is ideal for motors up to 15 kW, while PN 90651N is suitable for motors up to 150 kW.